Thermoworks 9009-B INDUSTRIAL DUAL-BLOCK CALIBRATOR Bedienungsanleitung Seite 37
- Seite / 45
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
33
8 Digital Communication Interface
Interface Commands
Command Description
Command
Format
†
Command
Example
‡
Returned
Returned
Example
Acceptable
Values
Calibration Parameters Menu
Read R0 calibration parameter r[0] r r0: 999.999 r0: 100.578
Set R0 calibration parameter to
n
r[0]=n r=100.324 100 to 105
Read ALPHA calibration
parameter
al[pha] al al: 9.9999999 al: 0.0038573
Set ALPHA calibration parameter
to
n
al[pha]=n al=0.0038433 0.002 to 0.006
Read DELTA calibration
parameter
de[lta] de de: 9.9999 de: 1.507
Set DELTA calibration parameter de[lta]=n de=1.3742 0.5 to 1.9
Read BETA calibration parameter be[ta] be Be: 9.999 be:0.342 —25 to 25
Set BETA calibration parameter be[ta]=n be=0.342
Miscellaneous
Read firmware version number *ver[sion] *ver ver.9999,9.99 ver.9009,1.21
Read structure of all commands h[elp] h list of commands
Read ALL operating parameters all all list of parameters
Legend: [] Optional Command data
{} Returns either information
n Numeric data supplied by user
9 Numeric data returned to user
x Character data returned to user
Note: When DUPLEX is set to FULL and a command is sent to READ, the command is returned followed by a
carriage return and linefeed. Then the value is returned as indicated in the RETURNED column.
†
Preface all commands with either C: (for cold side) or H: (for hot side). If the C: or H: is left off, the returned value is for the hot side.
‡
The returned command has either a ‘C’ or an ‘H’ before the colon depending on which side was queried.
9009 Communication Commands Continued
- User’ s Guide 1
- Rev. 6A0901 2
- Table of Contents 3
- 1.2 Safety Information 9
- 1 Before You Start 10
- Safety Information 10
- CAUTIONS 11
- Authorized Service Centers 12
- User’s Guide 13
- 2 Introduction 14
- Conditions 15
- 4 Quick Start 17
- 4.4 Setting the Temperature 18
- 4.5 Changing Display Units 18
- 5 Parts and Controls 19
- 5.3 Accessories 21
- 6 General Operation 22
- 7 Controller Operation 23
- Temperature Set-point 25
- 7.3 Scan 26
- 7.4 Secondary Menu 27
- 7.5 Heater Power 27
- 7.6 Proportional Band 27
- 7.7 Controller Configuration 29
- 7.8 Operating Parameters 29
- 7.10 Calibration Parameters 31
- 7.10.1 R0 32
- 7.10.2 ALPHA 32
- 7.10.3 DELTA 32
- 7.10.4 BETA (Low Temp Only) 32
- 8.1 Serial Communications 33
- 8.1.2 Setup 34
- 8.2 Interface Commands 35
- Interface Commands 37
- 9 Test Probe Calibration 38
- 10 Calibration Procedure 40
- 10.2.2 Compute R0 & ALPHA 41
- Calibration Procedure 42
- 11 Maintenance 43
- 12 Troubleshooting 44
Verwandte Produkte und Handbücher für Messgeräte Thermoworks 9009-B INDUSTRIAL DUAL-BLOCK CALIBRATOR
(6 Seiten)Cooper Lighting INVUE IMI-572 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Sztuczne oświetlenie Cooper Lighting INVUE IMI-572.
Dostarczamy 1 pdf podręczników Cooper Lighting INVUE IMI-572 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Kommentare zu diesen Handbüchern